Clik here to view.
Trim problem in xPCB Layout VX.1.1
As shown below,selectaLINEandArc,Trimtoolbarbutton is disabled. But ifthe leftstretchedLINEendpoint, theTrimbuttonisactivated. Theproblem is notevery time, in some casesthere will be, butI still have...
View ArticleClik here to view.
ddr read batch simulation
Hai In ddr3 batch the write leveling option is present ,similarly how or where read leveling settings are fed to the simulation engine ?Read leveling is implemented in the qoriq power pc...
View ArticleClik here to view.
NC symbol use
I defined nc symbol that looks like X and connected it tu unused pin at the designwhen I run verify procidure -unconnected pins check i still get error on that pinwhat i did wrong ?
View ArticleRe: Expedition 9.5 - Can only place a few vias in a conductive pad
Probably there is a clearance setting that is causing the problem. How to find out? - Turn off DRC checking- Add the Via's- Turn on DRC checking- Run a DRC on the via region to find out the problem.
View ArticleRe: NC symbol use
Is your symbol of type 'Annotate' and does it have a 'Term' property with no value?If so then try connecting the symbol to a net stub on the pin.
View ArticleRe: xDX Designer marquee multiple problems
No this is not a bug, Ctrl+Select first selects then de-selects and in VX.1 this was made to be consistent.
View ArticleRe: NC symbol use
Its annotate type with term property i tried to connect to stub but the rectangle at the end of the line stay there after puting the NC syblol,its seems that the symbol do not connects to the end of...
View ArticleRe: NC symbol use
Does it have a pin? The pin should be greater than 0 length to make connection easier.
View ArticleRe: xDX Designer marquee multiple problems
Ithink this isunreasonable, as shown above,sojustdeselect thenet, componentremainsin the selected state. Also, if I wantnetandcomponent in areas A andB, select all,howdoes it work?Hold down...
View ArticleRe: xDX Designer marquee multiple problems
I suggest you post an Idea on the ideas site if you require different behaviour. There seems to be inconsistency between nets and symbols, but in general successive use of Ctrl should select then...
View ArticleRe: xDX Designer marquee multiple problems
Why not select the whole circuit, then de-select the bottom right hand corner part.
View ArticleCan't use Cell- and Padstack Editor (faded tool/ tool not active/ can't click...
Hello, I have installed the version 7.9.5 of Expedition on Windows 7. In the part editor I can only create parts, but no padstacks or cells. I can use existing cells (in Pin Mapping) but not create...
View ArticleRe: Can't use Cell- and Padstack Editor (faded tool/ tool not active/ can't...
In the library manager interface you need to open the Padstack Editor & Cell Editor separately to create the new padstacks and cells and then associate them to a part in the Part Editor.If you...
View ArticleRe: xDX Designer marquee multiple problems
Or don't intersect with A when selecting the bottom section of B.
View ArticleRe: Expedition 9.5 - Can only place a few vias in a conductive pad
Charles, Great advice, Thank you. Ken
View ArticleClik here to view.
Re: xDX Designer marquee multiple problems
Figure A and B is just my example to illustrate this problem, marquee A and B, are different to select the whole circuit, then de-select the bottom right hand corner part, such deselect put some only...
View ArticleRe: xDX Designer marquee multiple problems
We use the shift key for a 'Smart' select - basically you preselect the object type you are interested in then 'Shift+Area Select' only selects objects of that type. What you're after is selection...
View ArticleRe: Can't use Cell- and Padstack Editor (faded tool/ tool not active/ can't...
Thank you very much. Now everything is as it should be. By the way: Very quick answering. Big thanks
View ArticleDrill holes missing in 3D view PADS Standard Plus VX1.2
hi all, Is there a way to switch on/off the visibility of drill holes in 3D view, or is this a SW problem?I did not find a way to see drill holes in 3D PCB view. In decal Editor 3D view drill holes are...
View ArticleRe: Drill holes missing in 3D view PADS Standard Plus VX1.2
In 3D view open Display Control and check mark Z-Axis scaling. Regards, Yan
View Article