Issues with partial vias in Router 9.5
I'm experiencing strange behavior with partial vias in my design. I select an object, press F3 to route a trace then hit CTRL-Left click to place a via. Partial via is selected. Router will place a...
View ArticleRe: Can I add multiple netname labels on the same page?
Not with any past or current releases of xDX Designer. This is a frequent request in the queue.
View ArticleRe: Issues with partial vias in Router 9.5
Hi David, I've moved your question to the PADS sub-community where it should get a quicker response. Best regards, Cathy Follow us on LinkedIn....
View ArticleRe: Can I add multiple netname labels on the same page?
This is the second highest vote scorer on the current Ideas list POST data and is planned for introduction in the VX.2 release mid next year.
View ArticleScript under EE7.9.5
Hi, It seems the Block.AddText command didn't work under the EE7.9.5 release! for each Line in LineList.ToArray() Block.AddText Line,X,Y Y=Y-DeltaY Next I looked the documentation but nothing...
View ArticleRe: Xpedition Enterprise schematic in read only mode
Hello, DxD asks users to perform Forward Annotation only when:(1) User closes xDX Designer(2) If there are pending Forward Annotation, it opens the dialog which explicitly asks users if they want to...
View ArticleClik here to view.
Re: IE3D port reference definition problem
Hi Weiming,from what you wrote it is hard to say why there is such big difference. It would require to have a look at what you extracted to HL3D. Regarding the usage of multiple reference layers it is...
View ArticleNC Symbol
Using Expedition Flow, both 7.9.1 and VX version. (problem is the same in both) We have created an NC schematic symbol as per Technote MG527127. Now when the this is used on schematic designs...
View ArticleClik here to view.
Designer Schematic/Layout Questions
Designer Schematic/Layout is so new. I can't find a thing about this suite. I only found the tutorials on eewiki.net from Digikey. Could someone guide me to more info? Is there are forum dedicated to...
View ArticleRe: Designer Schematic/Layout Questions
Hi Rodney,There is a Designer forum on the Digi-Key site. See TechXchange Electronics Technology Community - Forum for Electrical Engineers | DigiKey . Best of luck to you!- Cathy
View ArticleRe: NC Symbol
You cannot, the NC symbols remove the nets from CES & Layout. Sent from my HTC
View ArticleUncapped via under Component
Hello , The uncapped via under component is not working well. I had set up the component attribute properly as per the attached help file ,eventhough the vias are exposed under component ,this...
View ArticleRe: Uncapped via under Component
Sabitha - Thanks for your question. This community is for general comments/questions/suggestions on the overall community, and not for product specific questions. Which Mentor product are you using?...
View ArticleRe: Uncapped via under Component
Thanks for the kind response! . After changing the mentor graphics site ,I can not go directly to the valor DFM community …Can you please give the link for the Valor DFM /Valor NPI community so that I...
View ArticleClik here to view.
Generating layer stackup in drill drawing in PADS Layout
The attached script generates graphical layer stackup in 2D libary, which shall be imported in drill drawing through Drafting Toolbar > From library command.Thanks for the Mentor team in writing...
View ArticleClik here to view.
Generating layer stackup in drill drawing in PADS Layout
This script generates layer stackup graphics in 2D library, which shall be imported in drill drawing through Drafting Toolbar > From library command Thanks for Mentor team in writing the script.
View ArticleAdding wire bonds to bottom side die pins
Hi, are there any special pitfalls when using bottom (back) side die pins? I have no problems to add wires from die top side to bondpads on the top side (WB1 in attached picture). But when I try to add...
View ArticleDrill to drill error in stacked blind and buried via in Pads layout 9.5 ???
Hi everyone, I am working on 8-Layre stack-up board in PADS layout. I have blind VIA (L1-L2) and Buried Via (L2-L3). when I stacked blind and buried VIA, am getting Drill to Drill error.can anyone...
View ArticleRe: Drill to drill error in stacked blind and buried via in Pads layout 9.5 ???
Hello, Try to offset the Blind and Buried vias by 1 mil apart. Regards, Yan
View ArticleDisplay customer part number Capital Harness XC
How to change the style set to display the customer part number instead of the internal part number in Capital Harness XC?
View Article