Re: Capital launcher question
In a traditional Capital customer organization, we don't typically see a single user that works with both a schematic and a harness design abstraction. This is however quite common in a traditional...
View ArticleRe: Did Mentor Fix the "Remove unused pads" for High-Speed Signals?
Ugh ... I'm afraid the answer is NO. It appears the tool still uses the "copper-to-drill" rule once unused pads are removed. I even tried adding an anti-pad to the inner layer via pad stack definition...
View ArticleClik here to view.
How to deal with Connector's extra index no.
Hello All,In the above daigram there are 11 cavities,and wire no.are also 11 ,but there are 15 index number.how to avoid 4 index which has - in place of wireif anyone know how to avoid this...
View ArticleClik here to view.
Re: How to deal with Connector's extra index no.
Hello Rashila, I think you can hide empty cavities to get what you want. And one more thing, if you are now using release 2015.1 SP1606, you have to use below command to edit table in Style: Thanks...
View ArticleDDR4 model selection while simulating ADDRESS signal
As there is fly-by topology used in DDR4 address, command and control signals. I am doing address line signal integrity, as address line have I/O logic as SSTL12. But in ibis model it comes as three...
View ArticleRe: How to Convert DxDesigner schematics from PADS 2007 to PADS vx1.2?
I believe the .dproj file extension is created when you are using the Dashboard to create a new project? However I don't use Dashboard. I only use the DxDesigner vx1.2 while creating a new project...
View ArticleCapital Integrator - HDSI file - Not Contain Terminals
Hi, In topology (integrator), my HDSI in Bridge out command is not been builded with Terminals Part-numbers. What is necessary to make integrator to process Terminal part-numbers?
View ArticleClik here to view.
Re: How to Convert DxDesigner schematics from PADS 2007 to PADS vx1.2?
The dproj file is the old project file extension from earlier versions of the software (pre-iCDB), Because PADS changed to this version later than Xpedition and didn't use the same naming conventions,...
View ArticleRe: How to Convert DxDesigner schematics from PADS 2007 to PADS vx1.2?
I created the .dproj as per your above instructions but when I try to open it from Vx1.2 I get the foll. error message: " Cannot find xDX Designer data- 'sym' directory is missing"However if I change...
View ArticleRe: How to Convert DxDesigner schematics from PADS 2007 to PADS vx1.2?
Without the original project used to create the schematics I don't know of a method to get the schematics into VX.1.2. You could review the information provided on the migration community pages, but I...
View ArticleRe: Capital Integrator - HDSI file - Not Contain Terminals
Hi,Terminals are considered part of the harness specification and are therefore not specified in Integrator. Typically, terminal part numbers will be calculated and assigned in Capital Harness XC. Simon
View ArticleRe: Capital Integrator - HDSI file - Not Contain Terminals
which information is necessary to be enable to automatic select terminals in Harness XC?"Terminal Material Code - In Wire Atributes" or "Terminal material Drive - in Slot Connector" ?
View ArticleIntegrator - Wire - Attribute - Terminal Material Code - Automatic Selection
Hi, How can I do to make automatic the wire atribute "terminal Material Code" ? I already putted terminal material in capital logic in each pin from each device in "Contact material" attribute:Capital...
View ArticleMentor Graphics license manger fails to start.
Since patching my Solaris 10 server the Mentor Graphics license manager fails to start. I am getting the following error: MRI damon initialization error: FlexLM platform not enabled.
View ArticleLogical - Reducing Option Expression with Combination - where is it used?
I have a big option expression described below:(( EN_AP || EN_B4 || EN_BI || EN_XZ || EN_Y2 || EN_YD ) && TR_W7)This big expression could be described like DRGAT, I used a Combination to try to...
View ArticleRe: Capital Integrator - HDSI file - Not Contain Terminals
Hi Enio, There are various drivers to allow automatic terminal selection in XC. Please take a look at the following Community post which describes these: Terminal Plating Drivers in Capital Harness XC...
View ArticleRe: How to deal with Connector's extra index no.
Hi Zhiqiang,This is just to hide the emplty cavity.My question is different i just want to know there are only 11 cavity in the connectorbut index is showing 15 .why index is not 15 instead of 11.
View ArticleRe: How to deal with Connector's extra index no.
Hi RashilaPlease examine the component inside Capital Library.Is this a 15 cavity connector with a Symbol assigned that has only 11 locations?Note that if you have not assigned a Symbol inside Capital...
View ArticleRe: How to deal with Connector's extra index no.
Hi Pat san,thank you so much for your suggestion.connector is Accessing the default librery set,so problem is occuring.when location of symbol is set wthin in styling it work. RegardsRashila
View ArticleVX1.2 - Script - CellEditorGRAPHICS - Adding "Property_Text" in BATCH
Hello all,help me please.I need add to all my cells a new Property_Text property in batch by a script. (The result is on the picture - made manually).It is not possible to do by ALE.I didn't find a...
View Article