Clik here to view.
Clik here to view.
Re: How to make reuse to also remember refdes locations?
I once had a similar problem, for me the solution was to take this flag out.Give it a shot, may it helps
View ArticleRe: Hyperlynx DRC (Any Users?)
Hi Chris,We use Hyp DRC for a few of its out of the box features. I have not seen any value in developing custom checks, even though every time our sales rep mentions the tool he pushes the fact we...
View ArticleClik here to view.
Re: How to use antipad as route keepout?
It which tool? The best way to prevent this problem is better set up in layout. If you want to prevent traces from crossing anti pads increase the distance from traces to VIA, Pad and so on. Better...
View ArticleRe: License location does not contain a valid license
Hello, My recommendation is you open a new Service Request on SupportNet, that way we can take a closer look at your license file and setup, and hopefully get it working for you....
View ArticleRe: How to use antipad as route keepout?
Hi jay, Thanks for your response. I requested for pads layout in a particular through hole pins that I need to have its antipad as same as route keepout to prevent crossing the gnd void referenc of a...
View ArticleRe: How to make reuse to also remember refdes locations?
Hello and thank you for your suggestion! However I cannot find any menu/window like that. Is it in PADS Layout? I cannot seem to find pretty much any settings related to silkscreen DRC.
View ArticleClik here to view.
Re: How to make reuse to also remember refdes locations?
Hi Rafal I am sorry this is on Expedition, i was under the impression that they are very similar and that you hopefully have the same window somewear. You have a Editor Control in Pads? The Window is...
View ArticleRe: Show selected Variant in schematics border
Hello Raliesch, thank you very much. I thought it would be one easy step I missed, but maybe I was just to blind. Kind regards, Georg
View ArticleRe: Show selected Variant in schematics border
You are welcome, happens to everyone. Best regards.Ralf
View ArticleRe: How to make reuse to also remember refdes locations?
I figured it out. It seems the reference designator placement is not maintained in VX.1.1 (supposedly is maintained in earlier versions but I did not try it). But thankfully in VX.1.2 it works...
View ArticleRe: In Style Sets where has Cross-reference -> Wire-XREF gone?
Hi , How can i get this doc http://communities.mentor.com/docs/DOC-1573 from this site , i am getting the following error always . Access to this place or content is restricted. If you think this is...
View ArticleError 73740 (ie3dcpucore)
Hi! I'm new to IE3D/HyperLynx (v. 15.3) and I'm going through the training in the PDF User Guide. I was fine until I got to page 6-40, on batch simulating GDSII files through AGIF. When I attempt to...
View ArticleRe: License location does not contain a valid license
Thanks Andrew, When I go to that page I only see , "You may not access this page." I just purchased the software last week so I'm not sure why it is disabled for my account. Is there a phone number...
View ArticleRe: License location does not contain a valid license
Hi Thomas, Go ahead and call 1-800-547-4303, and enter "1" (Technical Support), then "0" (Help using support system), and the support coordinator team should be able to take care of the issue....
View ArticleRe: How to convert Eagle files to DxDesigner?
Hi Gary, this is an old thread and I'm new to the community. I have the same problem and looking for a solution. We have xDX Designer.GBS Install Id: 38956Flow Id: PADS VX.0Full Flow Name: PADS...
View ArticleRe: Nucleus readystart - Sourcery codebench is unlicensed
Hi David, Based on your licensing you do have the armsptarmeabi feature, but I'm not sure it's the same one that is being requested. If so, you may be experiencing a more general licensing issue. It...
View ArticleDatabase for DxDatabook
We use DxDatabook to manage the parametric database of our parts. Originally we started out with excel to drive odbc, then we moved to mysql and wrote a custom front end to the database for creating...
View ArticleRe: Error - Unable to check for update to PartQuest Tools installer
I recommend uninstalling and downloading a new update. We believe this is now corrected with the current install available from April 22, 2016. PartQuest Integration
View ArticleRe: How to make output warnings/links point to board section and not block...
So, I'm having problems with multi-level hierarchy and the link, so I unmarked this as correct. Basically, if I have: vdraw <severity> 1 <top/root block name> com...
View Article