Differential pairs exiting/entering IC's
Hello, I'm routing all kinds of different differential pairs (ethernet, PCIe, SATA, HDMI) but somehow I can't seem to let them normally enter or exit an IC.I think this is due to the differential...
View ArticleBus Ripper symbols point in the wrong direction + non-orthogonal segments
In the process of moving some stuff around, some nets off of a bus got disconnected. Restoring the connections result in the old style (diamond shaped) bus ripper symbol pointing in the wrong...
View ArticleClik here to view.
Re: how to get demonstration enable code for hyperlynx ?
Dear all,I have another issue with Hyperlynx SI I advanced to module 5 of demo:EMC Analysis .I setup below circuit and adjusted clock frequency to 133MHz (as tutor told)I observed about 15MHz skid to...
View ArticleLoss Snap to grid when Edit an existing Plane Shape
Hi, when i try to edit an Existing Plane Shape , for example i need to reduce a shape, moving a segment 45 degrees, this shape goes out of snap.If i move only a sigle point, by click on intersection...
View ArticleClik here to view.
wrong pin rotations after doing project integration in pcb
Hi All, Please help.I created a central library for a project, with cells all newly created.However, after I do project integration into pcb, the pins of some parts become rotated.The cells in my...
View ArticleClik here to view.
Update of @PRINTORDER fails
Currently we note an effect in an existing project during the update of the property @PRINTORDER which we can not explain.We procedures as follows:1. Generating the required PageOrder.txt2. Invoke...
View ArticleRe: Contributions/Progress erased
I must admit I'm confused why the concern?I was impressed with myself getting a nice high level but as far as I know my boss doesn't check this to give me a promotion. Cheers,Pat
View ArticleRe: Contributions/Progress erased
Why the concern?Well, when Mentor is introducing a new Communities platform then I want that everything works.But since the update its not working...It's now the second time the user progress was...
View ArticleRe: Contributions/Progress erased
Fair answer - shall wait to hear how it plays out.Regards,,Pat
View ArticlePartQuest error message
When a customer tries to use Part quest he gets this message.Any idea what is happening here?
View ArticlePADS 3D OPTION
Good evening everyoneI recently installed the PADS Layout VX version 1.2, everything works correctly, but the VIEW / PADS 3D menu l 'option is not enabled and I can not use it.Have I committed some...
View ArticleRe: PADS 3D OPTION
Hi Cristian, Are you sure that during the installation you chose the PADS 3D Plug in item in the installer (Product Selection tab) as I believe it is not selected by default? CheersOlivier
View ArticleCadra License not available
We got two new computers to replace two older ones. We reinstalled CADRA21 on both PCs. However, when running the software, we are getting License not Available. What do we need to do to get this...
View ArticleRe: PADS 3D OPTION
this should helphttps://supportnet.mentor.com/portal?do=reference.technote&id=MG592080&lang=en&prod=C115-S153-G192-P10548If your PADS Standard or Standard Plus seat is on maintenance, new...
View ArticleRe: PEX Pin Order
Hi Rajesh- According to "Methods for Correcting Pin Swapping" in the xRC manual (calbr_xrc_useref.pdf), the only restrictions are "a layout-based flow and the pins are on primitives or the top circuit...
View ArticleClik here to view.
Padsvx.1.2 display Bug!
Hello every body! Who can tell me how to do this problem? Is this bug?Windows 10 64bit，1366*768
View ArticleClik here to view.
Plow Interactive to any angle smt pads
Hi, in a project I had to place a so-dimm connector at 55 -degree. Pads 12x60th.With trace/clearance 0,15mm/0,15mm, plow interactive.To exit from pads, i must switch by press "F3" in any angle, with...
View ArticlePaste from layout clipboard results in the pasted silkscreen and assembly...
Hoping someone can help me with this. I paste from the layout clipboard an entire circuit that contains about 40 components. The components and traces are pasted correctly, however: 1. The refdes's...
View ArticleCan’t open FloTHERM XT 2.3 Software
In the installation process.Appear the following questions,How to solve.Error 1923.Service DTInterops(CoordinatorServiceHost) could not be installed.
View ArticleClik here to view.
Can’t open FloTHERM XT 2.3 Software
In the installation process.Appear the following questions,How to solve.Error 1923.Service DTInterops(CoordinatorServiceHost) could not be installed.
View Article