Quantcast
Channel: Mentor Graphics Communities: Message List
Browsing all 4541 articles
Browse latest View live

"Update Library" Command in the PADS 3D environment produces "Fatal Runtime...

When I use the "Update Library" Command in the PADS 3D View I get a "Fatal Runtime Error".I have tested on several designs but the same problem persists.This problem also occurs when I export a Step...

View Article


Re: Calculation of pour area

I don't think so. I have never seen it.I have heard CAM350 may have such a functionality - but I'm not sure. regardsKlaus

View Article


Image may be NSFW.
Clik here to view.

1 shematic pin assignment many pads cell

Hey. As in the creation of the one assigned to several pads scheme technical Pina? For example, to in Scheme I only tied line C1 and on the board it would be attached and C2? Thank you

View Article

Capital Integrator - Reports - Connectivity - Scheme - how to export?

A very handy way to set up reports to output. And you can Save As the Scheme to use your settings again. But is there way a way to allow other users to access those same Schemes?Or to bring that...

View Article

Re: Changing Part Numbers for PartQuest Parts in xDX Databook

I edit  PartQuest.mdb directly using Access to change the DEVICE property, the property that maps to PartType for the PADS VX.1.2 netlist flows.In the PADS Integrated flow using xDM Library Tools, Part...

View Article


Image may be NSFW.
Clik here to view.

Re: Problem in installing Design Kit

Hello, This is a question more suited to the PCB Community site:PCB Systems Design Or open a service request for assistance. Regards,Joy

View Article

Re: Lvs box black / gray Statement

If you look in the SVRF manual for LVS Box, it has a section title "Black and Grey Box Usage" that provides lots of details.

View Article

Image may be NSFW.
Clik here to view.

Re- Creating a Project in DxDesigner

I am trying to get a project to the latest revision.  I am unable to find the latest project revision but I do have the gerber files and the .ODB files. Is there any way to use either one of those...

View Article


Image may be NSFW.
Clik here to view.

Re: How to do "Layer Map" by name

Yes I think an alias capability should be good enough. In my case, the input GDS file has a different layer order (but the same layers) each time I perform simulation on it with the SVRF script. Thus I...

View Article


is there any script file for moving refdes ??

Hi everyone,In my Board 3000 components present,individual work will take time instead of that i planned to work in parallel.i found in pads layout placement work will do in parallel using (x and y...

View Article

CES rule pattern for higher voltage circuits

Hello everyone,i have a question.  For example you have a power rails GND, 300V and some circuit between them.Between power rails you need several mm clearance, but between circuit clearance can be...

View Article

Re: Contributions/Progress erased

Did they reset it again?Last week I was Level 9 Thinker, now I am Level 1 again and all my progress is lost... Come on, how often will they erase everything?  Starts to annoy.....

View Article

Custom Mask Display in Touchstone tool

Currently I am performing SI analysis for XAUI Interface.It is a 3.125Gbps link. We are generating S parameter file and analyzing Return Loss. In the XAUI Spec, Return loss Mask is defined as...

View Article


Re: CES rule pattern for higher voltage circuits

1) no way2) no way3) this is the way...

View Article

Re: Custom Mask Display in Touchstone tool

Use the protocol specific view of the Touchstone viewer

View Article


Clearance and net0

Hello, i have:class to class clearance:ISO1 - ISO2 -1mmdefault(with net0) - All - 0.1mm i need to be sure that ISO1 - ISO2 will not be violated thru unused N.C. pin pad with net0. Is it possible?

View Article

Re: Hyperlynx DRC (Any Users?)

Chris,I/we have been using Hyp DRC for just over a year now (with the VX1 design flow). I am not familiar with "Analysis Control", so I cannot respond to that part of your question.  However,...

View Article


Re: Hotkey (keybinding) for pop out of a hierarchical block in xDx Designer

There isn't a "pop" for a stroke but the last time this came up FileClose was determined to be 'close enough' You can bind Pop to a keystroke: Bindings("Schematic").AddKeyBinding "p", "Pop", Cmd, Key...

View Article

Image may be NSFW.
Clik here to view.

optional four million parts 3D library not for PADS Standard Plus users only...

For those of us that do not have PADS Professional but have Standard Plus, and don't have access to the optional four million parts 3D library.Here is access to over 9000 models for free...

View Article

Re: Capital Integrator - Reports - Connectivity - Scheme - how to export?

Hi Pat,I don't believe that this functionality is used very much. Like other user-specific data, the schemes are stored in the registry. It should be possible to export the registry node and re-import...

View Article
Browsing all 4541 articles
Browse latest View live