Suppress warning box when using ActiveDocument.ExportASCII
Greetings,In my vba script that I am writing I am using the command ActiveDocument.ExportASCII. Sometimes it generated a warning box like this: "problems detected during Database conversion. Show...
View ArticleRe: OPEN EFM SCRIPT AND CLOSE TO AVOID MULTIPLE ISTANCES
TheView.OpenDoc will open an efm file, and TheView.Cancel will close the current form. John
View ArticleClik here to view.
Sheet based net class assignment
I have attempted to setup sheet based net class in DxDesigner, but netlisting reveals this is being ignored. So I'll ask the community has anyone be able to set this up? PLease advise. Thank you folr...
View ArticleClik here to view.
Footprint with shorted pins
A lot of modern packages use large exposed pads which short multiple pins together. For example, package X2-DFN2020-6 from Diodes, Inc (see part DMP2039UFDE4). This part has pins 1, 2, 5, and 6 shorted...
View ArticleRe: Library Manager Exit or Quit issue
Hi, Now, the status of this defect is "Close".A sample script is the workaround which I got by this defect. I think that a possibility that update will be released is low since this defect has a...
View ArticleRe: Why Menu Bar does not work in Library Manager?
Hi, I also think that a possibility of being a defect is high.Please register on SupportNet or contact the support center of your region. Regards,Satoru
View ArticleRe: Sub-component problem
Hello LacIf your account is active then access to SupportNet should be possible.I would suggest you contact the person from whom your purchased the software and they will be able to confirm and assist...
View ArticleRe: Why Menu Bar does not work in Library Manager?
SR2696598672 opened as URL below. https://supportnet.mentor.com/portal?do=servicerequests.detail&sr=2696598672&lang=en&prod=C117-S113-G141-P10216
View ArticleRe: Footprint with shorted pins
And if I place an overlapping copper area shorting those pins in the footprint editor, it generates spacing errors and won't even let me route to a pin (because of the spacing errors). you can connect...
View ArticleRe: OPEN EFM SCRIPT AND CLOSE TO AVOID MULTIPLE ISTANCES
Thanks but it doesn't work. The main form launch a second form with the command TheView.OpenDoc but when the main form need to close the second form with the command TheView.close the main form closed...
View ArticleRe: Errors in routed paths
Hello, Thank you very much for your support and I was able to solve the issue.Thank you very much all
View ArticleRe: How to Register MGCPCB Command Class In C#
Hi, I even don't know where to begin, but you got all this wrong. If you handle a pcb document, you need to use the MGCPCB.Document class. The MGCPCB.Command is unrelated of any of your code.Also you...
View ArticleStackup editor in hyperlinks
Hi all, The stackup editor in xpedition xpcb layout designer is not the same as in hyperlinks stackup editor. When I open the layout design to do post layout simulation, Hyperlinks does not open the...
View ArticleSCRIPT FORM START-UP LOCATION
Hi, how can i set the start-up x,y position of a script? Thanks
View ArticleRe: Stackup editor in hyperlinks
Hi Supun, there are differences in the stackup edior that you open in PCB and HL Linesim and HL Boardsim.This differences are dependent on the version that you have of the tools. For this discussion I...
View ArticleClik here to view.
Re: Stackup editor in hyperlinks
Hi Milostink, Thank you for your fast response. I actually want to know what is the correct stackup ? . Which stackup details I should send to the manufacturer and simulations ? Thank you.
View ArticleRe: Change Policy
Hello, Pawel!Thanks for the quick reply!I have already tried to compare those elements from the exported templates, using to different versions of Capital: 201.1 and 2014.1.Using only Capital 201.1, I...
View ArticleRe: Change Policy
total amount of control objects get really changed somewhere between 2012.1 and 2013.1. In my opinion many of this objects in 2012.1 will never be needed to control by any policy. Hard to find a use...
View ArticlePREVENT FORM TO BE CLOSED WHEN PROJECT OPEN
Hi, i setted up Dxdesigner to open a Form (.efm file) (in Setup -> Settings -> Run On start-up -> Form:) but when i open the recent project in the welcome page the form is closed.How can i...
View Article