Re: TechNote MG579418: Calibre xRC error during PDB stage: Internal error -...
The answer was that some bad devices were being identified during lvsThese bad devices do not cause the LVS comparison to fail, but did result in the failure indicated when running XRC The solution is...
View ArticleRe: Can rules be assigned to standalone pins?
yes, it will work only with the pins having same rules and i not sure if there is any other net like thisBut i feel adding keepout is a better option than this , since it will indicate that there are...
View ArticleRe: How to fix the Decal Wizard in Layout and Option in Logic Problem
oh i forget to say i used window 8.1 64bit but i solved this problem.thanks for your comment
View ArticleRe: How to fix the Decal Wizard in Layout and Option in Logic Problem
so, is it because of the graphics drivers?
View Articlewhat is the use of Markups option in PADS 9.5 ??
Hi everyone,Let me explain any one what is the use of Markups option in Pads 9.5.How it will use ful ??please explain any one
View ArticleHow to separate PCB out of project?
I'm using EE 7.9.4.I would like to separate PCB file out of project. Anyone know how to do this.I tried to copy PCB folder to other location. So it read-only, can't use assign plane, can't use CES.
View ArticleCHS Licensing Error
After windows update in my laptop I am not able to checkout CHS license from server. I am getting an message that the program is not fully compatible with windows.
View ArticleRe: what is the use of Markups option in PADS 9.5 ??
markups are same as comments , when you are reviewing a design and want to add some comments you can do that using markups
View ArticleRe: How to fix the Decal Wizard in Layout and Option in Logic Problem
No, it is Value of powerlogicres.dll and powerpcbres.dll file problem.namely it is coordinate Value of Resource problem.i used tool 'reshack', i change the coordinate Value of Resource.in fact, i heard...
View ArticleRe: what is the use of Markups option in PADS 9.5 ??
while importing it's asking about the layer.i assigned one layer but i could not see any thing in this layer.
View ArticleUsing Constraints to Make PCB Layout Easier
Hey all, Just wanted to bring to your attention that Mentor's Vern Wnek has recently written an informative article for Printed Circuit Design & Fab on the pros and cons of using constraints. The...
View ArticleHow can I create versions of PCB saves? I'm using xPCB Layout VX.1
How can I create versions of PCB saves?
View ArticleRe: How can I create versions of PCB saves? I'm using xPCB Layout VX.1
Hi Gary, If you're managing versions in an enterprise environment, it's worthwhile to check out xDM Design. This is our design management tool that lets you check in schematics and PCB's into a vault -...
View ArticleHarness Loom Calculation
Hello all, I have a question- In a harness design, how does Vesys calculate the bundle diameter? In Project Preferences, under Harness, Harness Engineering, there is a "Bundle CSA Multiplication...
View ArticleRe: what is the use of Markups option in PADS 9.5 ??
just make sure that you assign some colors to the 2d lines and text in that layer
View ArticleTech Notes
Where can I get the Tech Note MG242600? I want to know what the parameter "Preserve Device Case" does. Thanks!
View ArticleDimensions in cell editor
I tried to verify the dimensions of a cell I drew with its datasheet. But I don't know how to measure the distances other than the pitch. I couldn't find the proper tools to measure other measurements.
View ArticleRe: what is the use of Markups option in PADS 9.5 ??
Hi,still i could not understand correctly.In Markups editer some details with issue details available (see image file 1) after that i export it from this board.i imported .cle file in another...
View Article