Re: Drawing Editor Font Arial - Extended Print is another Font, why?
Hallo Juergen, I completely agree with you.I just did some tests with VX.1.2 from Drawing Editor and with Extended Print and True Type Fonts (Arial).Without success. I really hoped that there would be...
View ArticleClik here to view.
line sim / board sim of ac coupled differential channel with bias resistors
Hi, I am simulating an ac coupled differential channel in linesim (it is exported from the board to line sim) the channel has differential driver driving 100 ohm diff lines to the receiver chip via ac...
View ArticleRe: Drawing Editor Font Arial - Extended Print is another Font, why?
Hallo Philipp, (CH=Schweiz?)... ich bin Österreicher. Wir verwenden std-proporional und hoffen im Pdf dann dass es passt. Man muss halt mehr Platz einrechnen oder es vorher austesten. Unter uns... Der...
View ArticleTo achieve low power with the scan flops during shifting
During Shift, the test data is being applied to both the scan path as well as to the combinational path.However, for Chain can we make sure to disable the test data to be loaded to the combinational...
View ArticleClik here to view.
Zoom to selection - completly unusable / uncomfortable ...
Dear community. Zoom to selection function: is completly unusable / uncomfortable because after zoom you see on your screen only one, big component only... I need do see this component in the center...
View ArticleRe: Zoom to selection - completly unusable / uncomfortable ...
Well, you can zoom out when the object is selected.Just scroll with your mouse wheel
View ArticleRe: Zoom to selection - completly unusable / uncomfortable ...
I agree with Philipp. The Zoom to Selected feature is an extremely good feature and using the scroll wheel to zoom out a little isn’t a problem.I think stating that the feature is “unusable /...
View ArticleClik here to view.
Re: CES rule pattern for higher voltage circuits
Absolutely option 3, that is the only way that the software can control the clearances. One of my latest designs had a Photo Multiplier Tube (PMT)on it that required voltages from 100V up to 1400V on...
View ArticleRe: Zoom to selection - completly unusable / uncomfortable ...
> Well, you can zoom out when the object is selected.> Just scroll with your mouse wheel Uncomfortable / waste of time... I have hundrets of test points to check. I need to just click on the list...
View ArticleRe: Zoom to selection - completly unusable / uncomfortable ...
Uncomfortable / waste of time... I have hundrets of test points to check. I need to just click on the list from left side, then I need to see selected testpoint and it's closest few components to see...
View ArticleRe: Zoom to selection - completly unusable / uncomfortable ...
HiSee Ideas D7238 and D7808. You can vote for them.However - I don't think it will help much. The ideas are more than 4 years old and nothing has happened. regardsKlaus
View ArticleRe: Zoom to selection - completly unusable / uncomfortable ...
I think the reason for the huge zoom in factor is the line thickness from the selected object.Because on a very big design it is helpful to have the object big on your screen otherwise you wont find it...
View ArticlexDx designer opens read only in xtream mode
Hi All, When I open xDx designer schematic in Vx1.1 xtream mode, Sheet open read only more and it's says like"Schematic is in read only mode (locked by Administrator on computer) .Kindly suggest How...
View ArticleClik here to view.
Synthesize Wire
Hello All! It's possible to change a wire configuartion after to do the Synthesize wire...? For example, I have this configuration:But I would like to have this: How Do I do it? How Do I remove this...
View ArticleRe: xDx designer opens read only in xtream mode
When you say xtream mode you mean you are opening the design in concurrent mode? If this is the case then you need to ensure the RSCM software is configured properly to allow multi-user access. The key...
View ArticleRe: PEX by area .
You can run PEX on cells, by making the cell the top cell in the LAYOUT PRIMARY statement. Parasitic extraction is based on connectivity, though, so simply doing a layout window through the entire...
View ArticleRe: Zoom to selection - completly unusable / uncomfortable ...
I think that what is missing is Pan to selection. A function that keeps the current zoom level of the page where the component is located and just centers the selection. Thankfully we have scripting...
View ArticleClik here to view.
Re: Zoom to selection - completly unusable / uncomfortable ...
Great and well working solution. Thanks a lot! :-) Best regardsMariusz
View ArticleLicense error [mgls_errno = 203] with latest HASP driver 7.41.0.0
Hi all, I'm running Xpedition VX.1.1 with a USB dongle on a Windows 7 prof. system with HASP driver 6.65.0.0 and everything is working fine.If I upgrade the HASP driver to version 7.41.0.0 then my...
View ArticleForward to PCB property does not exist
Referencing the recently updated MG547284 I set out to exclude from passing on to the net list a bunch of documentation items that we need to have on our parts lists. First problem encountered was the...
View Article