Re: Schematic net missing from pin in layout
click on pin 3 in the schematic, what are the values for the #= property?
View ArticleRe: Schematic net missing from pin in layout
There are no symbols in the schematic that allow me to highlight individual pins directly. I can add and remove net connections readily, but no resistor, IC, power or ground tap, connector, etc. etc....
View ArticleClik here to view.
Re: Schematic net missing from pin in layout
Using the selection filter, you can select pins directly, and then view the pin numbers in the property window. Using the symbol I sent you, I have pin 2 on the schematic selected, but on the symbol...
View ArticleClik here to view.
Re: Schematic net missing from pin in layout
The solution was to copy the schematic library symbol to another name. I used the library editor to copy my part definition in PADS to match. Suddenly my net connection worked. I reverted the name...
View ArticleHow do I add an obstruct to a custom RF shape?
I have run across a operation issue that I need assistance on. I create custom RF shapes all the time but usually are the simple type with conductive-shapes and nodes. Now I have a need for a more...
View ArticleClik here to view.
This is a test question - pls disregard
This question is just for testing a setting. Pls disregard.
View ArticleClik here to view.
in expedition VX 1.1 how do I exit The slection area mode
when I select set selection by polygon and start draw it i cant stop the mouse pointer to show the drawing line even if i switch to placment or other mode
View ArticleHow to make environment for calibre in cadence virtuoso, if both tool is on...
Both tool is on differemt server, then how can I make environment for calibre connect to virtuoso?
View ArticleRe: in VX1.1 howcan i place components directfrom dxd to pcb in cross prob
Has this been answered? If so please update the status, if not then get back to us.
View ArticleClik here to view.
Re: Unable to update the part number from Harness Design back to Schematic
Andrew, Vesys will allow different part numbers for schematic & harness. In order to update this you have to do resynchronise the harness after updating the schematic. For scaling the...
View ArticleRe: in expedition VX 1.1 how do I exit The slection area mode
Presumably to be a bug, it actually has quit this mode, just show the drawing line.I analyze because set selection draw, it ignores Draw grid, so hard to just your starting point on the Draw grid, when...
View ArticleClik here to view.
Re: in expedition VX 1.1 how do I exit The slection area mode
Forget that, at the end ofuse Close polygon commandcan avoidthis problem.
View ArticleClik here to view.
Packager without xDM Lib Parts (but with xDx Databook Parts)
Hi,Hope s.o. looking there.I'm using "netlist" project until now, and i'm trying to use now "integrated" project. I success with the "Starter Library" ( create a simple schematic, transfer to layout...
View ArticleClik here to view.
Getting cell name from odbc database
HiIn my organisation we are migrating from Altium Designer to Xpedition.And since we have solid database libraries of several thousands of components integrated with our ERP system, we would like to...
View ArticleClik here to view.
Re: How to combine wire 104E and 104?
Hello Eric To confirm if it has worked, please see the Browser list to the left of the diagram. In the example below, I have different Options on the two Wires. I then set a Rule so that only the Wires...
View ArticleClik here to view.
How to distinguish 'Plow Mode' and to 'get the trace object' selected during...
Hi,Below script is to get the Trace Object (Width of it)----------------------------------------------------------------------------Dim Traces,netLine, tempSet Traces =...
View ArticleRe: VeSys Harness 2.0: Is it possible to swap between part numbers on a...
Hi, could you please provide details about how to swap supplier part number in existing harness? currently I am using internal part numbers. Thanks,Jagadhees.
View ArticleRe: How to make environment for calibre in cadence virtuoso, if both tool is...
Hello, Cadence Virtuoso needs to be able to call the Calibre executable, so you need an NFS mount of the Calibre software to the Virtuoso system. For the remainder of the configuration, refer to the...
View ArticleClik here to view.
How to show comment in RDB for a Calibre DRC command file after encryption?
Dear All, As captioned, is there any method for this? Andrew Ng
View ArticleRe: How do I add an obstruct to a custom RF shape?
Larry - I just noticed your question. Thanks for posting it. This area of the communities is for questions on the communities in general, and/or suggestions for how to make them better. Product and...
View Article